1. Hazard Information

1.1 Physical Hazards

• • Falling Object Hazard: Incorrect fitting, loose fastening or failure of the retention system may cause the Slip-On Slate to detach and fall, potentially causing injury or property damage.
  • Insecure Fit: Use with an incompatible clapperboard may prevent the product from being securely retained.
  • Elastic Retention Hazard: Excessive stretching, pulling or deterioration of the elastic retaining strap may reduce its ability to securely hold the product.
  • Plastic Component Damage: Bending, folding, impact or excessive force may crack, warp or separate the layered plastic panels. Damaged edges may become sharp.
  • Fastening Failure: Worn, contaminated or improperly engaged hook-and-loop fastening may reduce holding strength and increase the risk of detachment.
  • Impact Hazard: Do not drop or throw the product.
  • Small/Damaged Parts: Broken or detached components may present an ingestion or choking hazard. Keep away from children.

1.2 Environmental Hazards

• • Wet-Weather Use: The product is designed for use in rain and wet production conditions. Prolonged storage while wet may cause deterioration of materials or fastening performance.
  • Heat Exposure: Excessive heat may deform the plastic components or affect the elastic and hook-and-loop materials.
  • Chemical Exposure: Strong solvents, cleaning chemicals or other incompatible substances may damage the plastic, elastic or fastening materials.

1.3 Misuse Hazards

• • Do not use as a handle for carrying the clapperboard.
  • Do not use for lifting, suspension, climbing or load-bearing applications.
  • Do not attach heavy equipment or excessive weight to the hook-and-loop surface.
  • Do not cut, drill, bend or otherwise modify the product.
  • Do not use with an incompatible clapperboard.
  • Not a toy. Keep away from children.
  • Do not place in the mouth or ingest any part of the product.

2. Risk Assessment

Overall Residual Risk: Low when the product is correctly installed, regularly inspected and used according to these instructions.

3. User Instructions for Safe Use

Before Use

1. Inspect the Slip-On Slate for cracks, deformation, separation, tears or other damage.
2. Inspect the rear elastic retaining strap for stretching, tearing or loss of tension.
3. Check that the hook-and-loop fastening is clean, undamaged and able to fasten securely.
4. Confirm that the clapperboard is compatible with the product.
5. Do not use the product if any component is damaged or unable to provide a secure fit.

Installation

1. Position the Slip-On Slate on the intended area of the compatible clapperboard.
2. Fit it carefully around the board without bending or forcing the plastic panels.
3. Position the rear elastic retaining strap around the board.
4. Fully secure the rear hook-and-loop fastening.
5. Ensure the product sits flat and securely against the slate.
6. Gently check the fit to ensure the Slip-On Slate cannot readily slide or detach.
7. Attach compatible Wet-Weather Tabs to the front soft-side hook-and-loop surface.

During Use

⚠ WARNING — FALLING OBJECT HAZARD
SECURE BEFORE USE. Ensure the Slip-On Slate is securely fitted and fastened to the clapperboard before every use.

• Do not use over people, animals or property where accidental detachment could cause injury or damage.
• Recheck the fastening if the slate has been dropped, knocked or subjected to significant movement.
• Do not carry the clapperboard using the Slip-On Slate.
• Do not excessively stretch the elastic retaining strap.
• Do not bend or fold the plastic body.
• Do not attach heavy equipment to the hook-and-loop surface.
• Do not throw or deliberately drop the product.
• Stop using the product immediately if it becomes loose or damaged.

Wet-Weather Use

The All-Weather Slip-On Slate is designed for use in rain and wet production conditions.

After wet use:

1. Remove attached Wet-Weather Tabs.
2. Remove the Slip-On Slate from the clapperboard.
3. Wipe away excess water.
4. Allow the product to air dry completely.
5. Do not store the product while wet or damp.

4. Maintenance and Disposal

4.1 Cleaning and Maintenance

• Inspect the product before each use.
• Keep the hook-and-loop surfaces free from dirt, fibres and debris that may reduce fastening performance.
• Wipe surfaces using a soft, damp cloth when necessary.
• Avoid abrasive cleaners and aggressive solvents.
• Allow the product to air dry naturally after exposure to moisture.
• Do not expose to excessive heat to accelerate drying.
• Regularly inspect the elastic strap, hook-and-loop fastening, plastic panels and joining points.
• Replace the product if the elastic loses tension or if any component becomes cracked, warped, torn, separated or unable to fasten securely.
• Do not attempt structural repairs or modifications that may affect safe retention.

4.2 Storage

• Store in a clean and dry environment.
• Store flat or in a position that does not permanently bend the plastic panels.
• Do not place heavy objects on top of the product.
• Avoid prolonged exposure to excessive heat or direct sunlight during storage.
• Ensure the product is completely dry before prolonged storage.

4.3 Disposal

• Dispose of the product responsibly in accordance with applicable local waste and recycling regulations.
• Where possible, separate recyclable components according to local recycling requirements.
• Do not burn or incinerate the product in household or open fires.

• Damaged products that can no longer be securely fitted should be permanently withdrawn from use and disposed of appropriately.

Disclaimer: This safety manual is provided for the safe and appropriate use of All-Weather Slip-On Slate. Failure to adhere to the guidelines may result in injury or damage, for which the manufacturer is not liable.

EU Declaration of Conformity

Manufacturer: Filmsticks Limited
Address: Unit 126i, Incubator Centre North East BIC, Wearfield Enterprise Park East, Sunderland, SR5 2TJ, UK
Model: Filmticks All-Weather Slip-On Slate
Intended Use: A removable wet-weather clapperboard accessory providing a soft-side hook-and-loop surface for attaching compatible Wet-Weather Tabs.

Filmsticks Limited has assessed the Filmsticks All-Weather Slip-On Slate, considering its intended use and reasonably foreseeable misuse. Identified risks are addressed through product design, installation requirements, compatibility limitations, inspection procedures, warnings and safety instructions.

When correctly fitted to a compatible clapperboard and used in accordance with the supplied instructions, the product is intended to meet the general safety requirements of Regulation (EU) 2023/988.

• General Product Safety Regulation (GPSR) (EU) 2023/988: Ensures that products placed on the EU market are safe for consumer use.

Applicable to the following Product Code:

FSOS

Authorised EU Representative:

Transcontinenta BV
Tarwestraat 29, 2153 GE Nieuw-Vennep, The Netherlands

Contact and Support
If you have any questions or concerns regarding this product, please contact us:

Email: info@filmsticks.co
Phone: +44 (0)1932 925100
Website:  www.filmsticks.co.uk

Click the button below to view the signed GPSR Compliance Statement