1. Hazard Information

The Filmsticks Clapper Stick is designed for safe and effective use in film production settings. However, improper handling or misuse may lead to certain hazards. The following hazard information is provided to ensure user safety:

Potential Hazards

• Pinching Hazard: Fingers may get pinched when snapping the clapper shut.

• Impact Injury: Improper handling can cause minor injuries from the clapper stick movement.
• Sharp Edges: Wear or damage may result in sharp edges, posing a cut risk.
• Breakage & Splintering: Excessive force or improper storage can cause breakage, leading to sharp fragments.
• Noise Levels: Repeated loud claps at close range may cause hearing discomfort or damage.

2. Risk Assessment

Likelihood of Hazards:

• Pinch injuries: Moderate (with improper handling)
• Impact injuries: Low (if proper handling techniques are followed)
• Cuts: Low (if inspected and maintained)

Control Measures:

• Handle the clapper stick by designated non-clapping areas to avoid pinching injuries.
• Use moderate force when clapping to prevent excessive noise and potential injury.
• Inspect the clapper stick regularly for signs of wear, splintering, or damage. Replace if necessary.

Residual Risk: When used according to the manual, risks are minimal. Adherence to this safety guidance ensures compliance with the General Product Safety Regulation (GPSR) requirements.

3. User Instructions for Safe Use

• Always handle the clapper stick by its edges or non-moving parts to avoid pinch points.
• Ensure that the clapper stick is firmly attached to the clapperboard (if applicable) before use.
• Check for loose screws, damage, or misalignment before use.
• Do not use excessive force when clapping to avoid damage to the product or injury.
• Store the clapper stick in a cool, dry place when not in use to prevent material degradation.
• Keep away from children and pets to prevent accidental misuse or injury.
• Clean the clapper stick with a soft, damp cloth. Avoid abrasive cleaners or tools that may damage the surface.
• If any damage is detected, replace the clapper stick immediately to avoid hazards.

Disclaimer: This safety manual is provided for the safe and appropriate use of Clapper Stick. Failure to adhere to the guidelines may result in injury or damage, for which the manufacturer is not liable.

EU Declaration of Conformity

Importer: Filmsticks Limited
Address: Unit 126i, Incubator Centre North East BIC, Wearfield Enterprise Park East, Sunderland, SR5 2TJ, UK
Model: Filmsticks Clapper Stick
Intended Use: Film production accessory

Filmsticks Limited has assessed the Filmsticks Clapperstick, considering their intended use and reasonably foreseeable misuse. The product addresses identified risks through product design, compatibility limitations, inspection procedures, warnings, and safety instructions.

When correctly used in accordance with the supplied instructions, the product is intended to meet the following EU directives and standards:

• General Product Safety Regulation (GPSR) (EU) 2023/988: Ensures that products placed on the EU market are safe for consumer use.
• EN ISO 2380-2:2004 – Assembly tools for screws and nuts — Screwdrivers for slotted-head screws — Part 2: General requirements, lengths of blades, and marking of hand-operated screwdrivers.

Applicable to the following Product Code:

FCSL
FCSM
FCSS
FCST
FCSN
FCSM-4130
FCSS-4130
FCST-4130
FCSJ-4130
FCSM-4130/GS
FCSS-4130/GS
FCST-4130/GS
FCSM-4130/BW
FCSS-4130/BW
FCST-4130/BW
FCSM-TIMECODE

Authorised EU Representative:

Transcontinenta BV
Tarwestraat 29, 2153 GE Nieuw-Vennep, The Netherlands

Contact and Support
If you have any questions or concerns regarding this product, please contact us:

Email: info@filmsticks.co
Phone: +44 (0)1932 925100
Website:  www.filmsticks.co.uk

Click the button below to view the signed GPSR Compliance Statement