1. Hazard Information

The Filmsticks T-Handle Screwdriver is designed for safe use. However, improper handling or misuse may pose the following risks:

• Physical Hazards:
  • Impact Hazard: Improper use may lead to hand injuries or damage to equipment if excessive force is applied.
  • Slip Hazard: The screwdriver may slip off the screw head, causing potential injury or scratches on equipment.
  • Sharp Edges: Damaged or worn-out carbon steel tips may develop sharp edges that could cause cuts.
• Material Hazards:
  • Handle Material (ABS Plastic): Exposure to excessive heat may cause deformation or weakening of the handle.
  • Shaft Material (Carbon Steel): Corrosion may occur if exposed to moisture for prolonged periods, reducing effectiveness and safety.
    
    
• Choking Hazard:
  • Small detachable parts or damaged pieces may pose a choking risk to children. Keep out of reach of children.
    
    

2. Risk Assessment

Likelihood of Hazards:

• Hand injuries: Moderate (if improper force is applied)
• Slips: Low to Moderate (depending on correct use)
• Cuts: Low (if tool is inspected regularly)
• Choking: Low (if stored safely)
• Corrosion: Low (if maintained properly)

Control Measures:

• Always use the screwdriver for its intended purpose and avoid applying excessive force.
• Ensure the screwdriver tip matches the screw head size to minimize slipping.
• Inspect the tool regularly for signs of wear, corrosion, or damage, and replace if necessary.
• Store in a dry location to prevent moisture exposure and handle deformation.
• Keep out of reach of children to avoid choking hazards.
  
  

Residual Risk: When used as intended, risks are minimal. Adherence to these safety guidelines ensures compliance with the General Product Safety Regulation (GPSR) requirements.

3. User Instructions for Safe Use

• Align the screwdriver tip with the screw head before applying pressure to prevent slippage.
• Use moderate force to tighten or loosen screws. Do not use the tool for prying or levering.
• Ensure your hand grip is firm and stable on the ABS handle to prevent accidental slips.
• Avoid exposing the screwdriver to high temperatures or direct sunlight for extended periods.
• After use, clean the tool with a dry cloth to remove dust or debris.
• Inspect for wear or corrosion, especially on the carbon steel shaft. Replace if damage is observed.
• Store in a clean, dry location when not in use.
  
  

4. Maintenance and Disposal

• Clean the screwdriver with a dry cloth or mild detergent. Avoid abrasive cleaning agents.
• Periodically apply a light coat of anti-rust oil to the carbon steel shaft to prevent corrosion.
• Dispose of damaged or worn-out screwdrivers in accordance with local waste disposal regulations for metal and plastic materials.
  
  

Disclaimer: This safety manual is provided for the safe and appropriate use of the T-Handle Screwdriver. Failure to adhere to the guidelines may result in injury or damage, for which the manufacturer is not liable.

EU Declaration of Conformity

Manufacturer: Filmsticks Limited
Address: Unit 126i, Incubator Centre North East BIC, Wearfield Enterprise Park East, Sunderland, SR5 2TJ, UK
Model: Filmsticks T-Handle Screwdriver
Intended Use: Mounting and securing camera plates and compatible equipment

Filmsticks Limited has assessed the Filmsticks T-handle Screwdriver, considering their intended use and reasonably foreseeable misuse. The product addresses identified risks through product design, compatibility limitations, inspection procedures, warnings, and safety instructions.

When correctly used in accordance with the supplied instructions, the product is intended to meet the following EU directives and standards:

• General Product Safety Regulation (GPSR) (EU) 2023/988: Ensures that products placed on the EU market are safe for consumer use.
• EN ISO 2380-2:2004 – Assembly tools for screws and nuts — Screwdrivers for slotted-head screws — Part 2: General requirements, lengths of blades, and marking of hand-operated screwdrivers.

Applicable to the following Product Code:

FTHANDLE-SD-RED
FTHANDLE-SD-BLACK
FTHANDLE-SD-L-RED
FTHANDLE-SD-L-BLACK

Authorised EU Representative:

Transcontinenta BV
Tarwestraat 29, 2153 GE Nieuw-Vennep, The Netherlands

Contact and Support
If you have any questions or concerns regarding this product, please contact us:

Email: info@filmsticks.co
Phone: +44 (0)1932 925100
Website:  www.filmsticks.co.uk

Click the button below to view the signed GPSR Compliance Statement